5291-rf-cisco - Cisco Support Community

Transcript

RightFax and Cisco Cisco Unity Fax Solutions: Unity Fax Server Remote Access Exchange Message Store Cisco Unity Fax Server Cisco Unity Messaging Server PSTN E1/FXS F T.38 Outlook Client Outlook Client Web Client Cisco Call Control Server 2 Brooktrout Fax Boards ► 4 Port Analog Card ► 8,16,24,32 Port E1/T.38 ► No IP support ► Used in E1 or T.38 Mode ► Full size PCI Card ► Full size PCI Card ► Ethernet and E1 Ports 3 Unity Fax Server TR1034 TDM Configuration Remote Access MCS Server Q.931 |||| Brooktrout TR1034 T38 Card IP Network E1/FXS PBX or Router E1 |||| MCS built-in LAN ► When operating in TDM the Fax Server uses E1 for Fax reception ► Application access is via MCS Network Interface ► Can be used in a TDM/IP migration 4 Unity Fax Server TR114 Analog Configuration MCS Server E1/FXS E1 |||| Router POTS Dial-peer for Fax Brooktrout TR114 SIP |||| MCS Network Card ► When operating in T.38 mode the Fax Server uses two network connections ► SIP and Application access on MCS Network Interface ► RTP/Media is sent to Brooktrout Ethernet Interface 5 Unity Fax Server TR1034 T.38 Configuration Remote Access MCS Server E1 RTP E1/FXS |||| Brooktrout TR1034 T38 Card RTP SIP Router (T.38dial-peer points at MCS Network Card) SIP |||| MCS Network Interface ► When operating in T.38 mode the Fax Server uses two network connections ► SIP and Application access on MCS Network Interface ► RTP/Media is sent to Brooktrout Ethernet Interface 6 Unity Fax Server TR1034 T.38 Configuration Cisco Fax Server (CFS) IOS Router Fax DN=8000 8000 DN=5xxx 5xxx FXS .254 .207 .208 10.1.1.0/24 ► In this network we want route fax calls from the fax to the CFS server using SIP ► We want to route all 4 digit DNs starting with 5 to the CFS ► We need to build dial peers in the router to achieve this 7 Basic Router Configuration hostname Voice_gateway enable password cisco Set Host Name interface FastEthernet0/0 Enable Password ip address 10.1.1.254 255.255.255.0 duplex auto speed auto no shut line vty 0 4 Ethernet Interface configuration Telnet Configuration exec-timeout 120 0 password cisco login 8 PSTN to IOS Inbound Config VOIP Dial Peer Tag dial-peer voice 5000 voip description Cisco Fax Server Calls destination-pattern 5... session protocol sipv2 session target ipv4:10.52.200.207 session transport udp codec g711ulaw fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco Destination Pattern to match Specify SIP as call control protocol IP address of RF Server (NOT BT Card) Configure SIP to use UDP packets Set the default codec for this dialpeer Set Fax relay mode to T.38 Alternatively "voice service voip" and "Voice class codec" could be used for Fax and codec selection 9 Unity Fax Server TR1034 T.38 Configuration Cisco Fax Server (CFS) IOS Router Fax DN=8000 8000 DN=5xxx 5xxx FXS .254 .207 .208 10.1.1.0/24 ► We want to route all 4 digit DNs starting with 8 to the PSTN ► We need to build dial peers in the router to achieve this 10 PSTN to IOS Inbound Config POTS Dial Peer Tag dial-peer voice 8000 pots destination-pattern 8... no digit-strip port 1/0/0 dial-peer voice 1 voip description generic incoming dial-peer incoming called-number .T Destination Pattern to match Specify SIP as call control protocol Inbound VOIP dial-peer Match all in bound VOIP Calls codec g711ulaw fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco Set the default codec for this dialpeer Set Fax relay mode to T.38 Alternatively "voice service voip" and "Voice class codec" could be used for Fax and codec selection 11 Unity Fax Server Call Manager Deployment Multi-Function Document Device H.323 Fax Client Email Client SIP(T.38) Cisco Call Manager Cisco Fax Server Messaging Server Cisco Unity Server 12 Unity Fax Server TR1034 T.38 Configuration Cisco Fax Server (CFS) IOS Router Fax DN=8000 8000 DN=5xxx 5xxx FXS .207 .254 10.1.1.0/24 .201 Call Manager ► .208 IP Phones If we need to also route calls to a Cisco Call manager we add a H.323 dial-peer to the router 13 PSTN to IOS Inbound Config POTS Dial Peer Tag dial-peer voice 2000 voip description Dial-Peer to Call manager destination-pattern 2... session target ipv4:10.52.200.201 Destination Pattern to match IP Address of Call Manager codec g711ulaw Set the default codec for this dialpeer Alternatively "voice service voip" and "Voice class codec" could be used for Fax and codec selection14