Designati Desi gnation: on: A 625/A 625M – 03
Standard Speciﬁcation for
Tin Mill Products, Black Plate, Single-Reduced 1 This standard is issued under the ﬁxed designation designation A 625/A625M; the number immediately following following the designation designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Sco Scope pe
184.108.40.206 3.1.2. 3 Che Chemic micall ally y tre treate ated d and oil oiled ed (se (seee Spe Speciﬁ ciﬁcat cation ion A 623 or Speciﬁcation A 623M). 3.1.3 Thick Thickness ness (see Speci Speciﬁcat ﬁcation ion A 623 or Speci Speciﬁcati ﬁcation on A 623M). 3.1.4 Wi Width. dth. 3.1.5 Lengt Length, h, for cut size sizess only. 3.1.6 Rolling direction must must be speciﬁed by underlining underlining the steel (rolling width) for cut sizes. 3.1.7 Steel type (see Speciﬁcation Speciﬁcation A 623 623 or Speci Speciﬁcati ﬁcation on A 623M). 3.1.8 Mecha Mechanical nical desi designati gnation on requi requireme rements nts (see Speci Speciﬁcaﬁcation A 623 or Speciﬁcation A 623M). 3.1.9 Intended application. application. 3.1.10 Quant Quantity ity,, in base boxes [SITAs] [SITAs] (see Note 5). 3.1.11 3.1.1 1 On coils coils,, spec specify ify minimum of range or acce acceptabl ptablee inside insi de diam diameters eters.. The stan standard dard insi inside de diame diameter ter is appr approxioximately 16 in. if ordered to Speciﬁcation A 625 [410 mm if ordered to Speciﬁcation A 625M]. Coils should be speciﬁed to a maximum coil weight if ordered ordered to Speciﬁcation A 625 [mass if ord ordere ered d to Spe Speciﬁ ciﬁcat cation ion A 625 625M] M] or max maxim imum um out outsid sidee diameter, or both. 3.1.12 Packa Packaging ging.. 3.1.13 ASTM speciﬁcatio speciﬁcation n desig designatio nation n and year of issu issue. e. 3.1.14 Special requirements, requirements, where applicable.
1.1 Thi Thiss spe speciﬁ ciﬁcat cation ion cov covers ers sin single gle-re -reduc duced ed bla black ck pla plate te produced from low carbo produced carbon, n, coldcold-redu reduced ced stee steel, l, furn furnished ished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications. 1.2 It may be supplied supplied dry or oil oiled ed and wit with h or without without surface surfa ce trea treatmen tment. t. This produ product ct is norm normally ally supplied supplied with a trimmed edge. 1.3 1. 3 Th This is sp spec eciﬁ iﬁca cati tion on is ap appl plic icab able le to or orde ders rs in ei eith ther er inch-pound units (as A 625), which is supplied in thicknesses from 128-lb base weight (0.0141 in.) and lighter, or SI units (as A 625M), which is supplied in thicknesses from 0.358 mm and lighter. 1.4 The values values stated in either either inch-pound inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in bra bracke ckets. ts. The val values ues stated stated in eac each h sys system tem are not exact equivalen equiv alents; ts; therefore, therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this speciﬁcation. 2. Referenced Documents 2.1 ASTM Standards: A 623 Speciﬁcation for Tin Mill Products, General RequireRequire2 ments A 623M 623M Speci Speciﬁcati ﬁcation on for Tin Mill Products, Products, Gener General al Re2 quirements [Metric]
NOTE 1—A typical ordering description is as follows: 1000 Base Boxes, Single-Reduced Black Plate, oiled, 80 lb base weight, 30 in. by coil, MR, T5CA for lithographed can bodies to ASTM A 625/A 625M - XX. [600 SITAs, Single-Reduced Black Plate, oiled, 0.25 mm, 810 mm by coil, MR, T5CA for lithographed can bodies to Speciﬁcation A 625/A 625M. NOTE 2—A typical typical ordering description description for cut sizes is as follows: 500 Base Boxes, Single Reduced Black Plate, oiled, 80 lb base weight MR, T-2 BA, 7C, 303 ⁄ 4 in. by 307 ⁄ 16 16 in., for lithographed can bodies in accordance with Speci Speciﬁcation ﬁcation A 625/A 625M - XX. [100 SIT SITAS, AS, Single Reduce Reduced d Black Plate, oiled, MR, T-2 BA, 7C, 0.28 mm thickness, 781 by 773 mm, for lithographed can bodies in accord accordance ance with Speciﬁ Speciﬁcation cation A 625M/ A 625M - XX.] NOTE 3—The production production of coils does not af afford ford the same opportunity for inspection, grading, and sorting as does the production of cut sizes. Accordingly, appropriate processing and quality control procedures are required by the purchaser to obtain optimum utilization of the material. Cut sizes are line-inspected line-inspected visually and mecha mechanically nically during production. Sheets She ets hav having ing sur surfac facee impe imperfe rfecti ctions ons tha thatt wil willl not inte interfe rfere re with thei theirr utilizations utiliza tions are include included. d.
3. Order Ordering ing Information Information 3.1 Orders for product under this this speciﬁcation shall shall include the fol follow lowing ing inf inform ormati ation, on, as req requir uired ed and app applic licabl able, e, to adequately describe the desired materials. 3.1.1 Name of produ product ct (sin (single-r gle-reduce educed d blac black k plat plate). e). 3.1.2 Surfa Surface ce appearance appearance and ﬁnish (Section (Section 4). 220.127.116.11 Dry Dry.. 18.104.22.168 Oiled (type of oil; oil; mineral or suitable suitable for lithographlithographing) (Section 5). 1
This speciﬁcation speciﬁcation is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel, and Related Alloys and is the direct responsibility of Subcommittee A01.20 on Tin Mill Products. Currentt edition approved September Curren September 10, 2003. Publi Published shed November 2003. Originally Origin ally approved in 1968 1968.. Last previous edition approved in 1998 as A 625/ A 625M – 98. 2 Vol 01.06. Annual Book of ASTM Standard Standards, s, Vol
NOTE 4—Single-reduced black plate is highly susceptible to rusting and must be properly handled during transit and storage.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
A 625/A 625M – 03 22.214.171.124 7C —A smooth ﬁnish with grit lines. The surface roughness will range from 10 to 25 µin. Ra [0.254 to 0.635 µm Ra]. This is the standard ﬁnish for tin mill products. 4.1.2 Blasted and/or Otherwise Textured Roll Finishes : 126.96.36.199 5A—A shot-blasted ﬁnish (SBF) intended for lithographing. 188.8.131.52 5C —A shot-blasted ﬁnish (SBF) for general applications. The surface roughness will range from 30 to 60 µin. Ra [0.760 to 1.52 µm Ra].
NOTE 5—In inch-pound units single-reduced black plate is supplied on an area basis expressed in base boxes. In coils, the number of base boxes is computed from the measured length and the speciﬁed width. In cut lengths, the number of base boxes is computed from the speciﬁed length and width dimensions and sheet count. For calculating mass, the density of steel for tin mill products is 0.2836 lbf/in.3. In SI units single-reduced black plate is supplied on an area basis computed in SITAs. In coils, the number of SITAs is computed from the speciﬁed length and the speciﬁed width. In cut lengths, the number of SITAs is computed from the speciﬁed length and width dimensions and sheet count. For calculating mass, the density of steel for tin mill tests is 7850 kg/m2.
5. Oiling 4. Surface Appearance and Finish
5.1 Black plate is furnished oiled or dry. Unless indicated by the purchaser, single-reduced black plate will be supplied dry. Any required oiling treatment will be negotiated between the purchaser and the supplier.
4.1 Surface Appearance—Single-reduced black plate is customarily produced with ground roll and shot-blasted roll ﬁnishes as follows: 4.1.1 Ground-Roll Finishes : 184.108.40.206 7A—A lustrous smooth ﬁnish intended for electroplating by the purchaser. 220.127.116.11 7B—A smooth ﬁnish that may contain ﬁne grit lines. This ﬁnish is speciﬁed for special applications.
6. General Requirements for Delivery 6.1 Product furnished under this speciﬁcation shall conform to the applicable requirements of the current edition of Speciﬁcation A 623 or Speciﬁcation A 623M unless otherwise provided herein.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ﬁve years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected]
(e-mail); or through the ASTM website (www.astm.org).