Preview only show first 10 pages with watermark. For full document please download

A492-95(2013) Standard Specification For Stainless Steel Rope Wire

Descripción: A492-95(2013) Standard Specification for Stainless Steel Rope Wire

   EMBED


Share

Transcript

Designation: A492 − 95 (Reapproved 2013) Standard Specification for Stainless Steel Rope Wire1 This standard is issued under the fixed designation A492; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense. 3.2 If possible, the intended end use of the item should be given on the purchase order, especially when the item is ordered for a specific end use or uses. 1. Scope 1.1 This specification covers the more commonly used types of round stainless steel wire intended especially for stranding into wire rope. NOTE 1—A typical ordering description is as follows: 1000 lb stainless steel, cold-drawn, bright-finish, wire, 0.009-in. diameter, spools. Type 304, ASTM Specification A492 dated , End Use . 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 4. Chemical Composition 4.1 The steel shall conform to the requirements as to chemical composition specified in Table 1. 2. Referenced Documents 4.2 Methods and practices relating to chemical analysis required by this specification shall be in accordance with Test Methods, Practices, and Terminology A751. 2.1 ASTM Standards:2 A555/A555M Specification for General Requirements for Stainless Steel Wire and Wire Rods A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products 5. Condition 5.1 The wire is cold drawn and furnished in the finish (see Section 7) specified on the purchase order. 3. Ordering Information 3.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this specification. Such requirements may include, but are not limited to the following: 3.1.1 Quantity (weight), 3.1.2 Name of material (stainless steel), 3.1.3 Condition (see Section 5), 3.1.4 Finish (see Section 7), 3.1.5 Cross section (round), 3.1.6 Form (wire), 3.1.7 Applicable dimensions (diameter), 3.1.8 Type designation (Table 1), 3.1.9 ASTM designation and date of issue, and 3.1.10 Special requirements. 6. Mechanical Requirements 6.1 The material shall conform to the requirements as to mechanical properties specified in Table 2. 7. Finish 7.1 The types of finish procurable are pickled finish and bright finish (available only in sizes that can be diamond drawn, which are generally 0.045 in. (1.14 mm) and smaller). 8. General Requirements for Delivery 8.1 In addition to the requirements of this specification, all requirements of the current edition of Specification A555/ A555M, shall apply. Failure to comply with the general requirements of Specification A555/A555M constitutes nonconformance with this specification. 1 This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17 on Flat-Rolled and Wrought Stainless Steel. Current edition approved Oct. 1, 2013. Published October 2013. Originally approved in 1963. Last previous edition approved in 2009 as A492 – 95 (2009). DOI: 10.1520/A0492-95R13. 2 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [email protected] For Annual Book of ASTM Standards volume information, refer to the standard’s Document Summary page on the ASTM website. 9. Packaging and Package Marking 9.1 Each coil or spool shall be one continuous length of wire. Each coil shall be firmly tied and each spool shall be tightly wound. Unless otherwise specified, coils shall be placed in drums or paper wrapped and spools shall be boxed in such a manner as to assure safe delivery to their designation when properly transported by any common carrier. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States 1 A492 − 95 (2013) TABLE 1 Chemical Requirements UNS Designation S S S S S S A 21600 21603 30200 30400 30500 31600 Composition, % Type XM-17 XM-18 302 304 305 316 Carbon, max 0.08 0.03 0.15 0.08 0.12 0.08 Manganese 7.50–9.00 7.50–9.00 2.00 2.00 2.00 2.00 Phosphorus, max Sulfur, max Silicon, max Chromium Nickel 0.045 0.045 0.045 0.045 0.045 0.045 0.030 0.030 0.030 0.030 0.030 0.030 1.00 1.00 1.00 1.00 1.00 1.00 17.50–22.00 17.50–22.00 17.00–19.00 18.00–20.00 17.00–19.00 16.00–18.00 5.00–7.00 5.00–7.00 8.00–10.00 8.00–10.50 10.50–13.00 10.00–14.00 Molybdenum NitrogenA 2.00–3.00 2.00–3.00 ... ... ... 2.00–3.00 0.25–0.50 0.25–0.50 0.10 0.10 ... 0.10 Maximum unless otherwise indicated. TABLE 2 Tensile Strength Requirements For Types XM-17, XM-18, 302, and 304 min Diameter, in. (mm) psi 0.007 (0.18) and smaller Over 0.007 (0.18) to 0.010 Over 0.010 (0.25) to 0.015 Over 0.015 (0.38) to 0.019 Over 0.019 (0.48) to 0.025 Over 0.025 (0.64) to 0.030 Over 0.030 (0.76) to 0.035 Over 0.035 (0.89) to 0.040 Over 0.040 (1.02) to 0.050 Over 0.050 (1.27) to 0.060 Over 0.060 (1.52) to 0.070 Over 0.070 (1.78) to 0.080 Over 0.080 (2.03) to 0.090 Over 0.090 (2.29) to 0.100 (0.25), (0.38), (0.48), (0.64), (0.76), (0.89), (1.02), (1.27), (1.52), (1.78), (2.03), (2.29), (2.54), incl incl incl incl incl incl incl incl incl incl incl incl incl 320 312 310 305 295 285 275 260 255 250 245 240 240 235 000 000 000 000 000 000 000 000 000 000 000 000 000 000 For Types 305 and 316 max MPa 2210 2150 2140 2100 2030 1960 1900 1790 1760 1720 1690 1650 1650 1620 9.2 Each coil or spool of wire shall be properly tagged showing heat number, grade, condition, ASTM specification number, and size. psi 355 350 345 340 330 315 310 300 285 280 275 270 270 265 000 000 000 000 000 000 000 000 000 000 000 000 000 000 min MPa 2450 2410 2380 2340 2280 2170 2140 2070 1970 1930 1900 1860 1860 1830 psi 245 245 240 240 235 235 235 235 230 225 220 210 210 205 000 000 000 000 000 000 000 000 000 000 000 000 000 000 MPa 1690 1690 1650 1650 1620 1620 1620 1620 1590 1550 1520 1450 1450 1410 10. Keywords 10.1 austenitic stainless steel; stainless steel rope wire ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website (www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/ COPYRIGHT/). 2