Preview only show first 10 pages with watermark. For full document please download


Descripción: Norma astm




Designation: E125 – 63 (Reapproved 2008) Standard Reference Photographs for Magnetic Particle Indications on Ferrous Castings 1 This standard is issued under the fixed designation E125; the number immediately following the designation indicates the year of  original origin al adoption or, in the case of revis revision, ion, the year of last revision. revision. A number in paren parenthese thesess indicates the year of last reappr reapproval. oval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense. These Reference Radiographs have been approved  to replace MIL-M-11473 (ORD). These Reference Photographs2 have been reproduced through the courtesy of the Steel Founders’ Society from photographs obtained from its member companies. 1. Sco Scope pe 1.1 This collection of reference photographs photographs covers types and degrees of discontinuities occurring in steel castings and other types of ferrous castings detectable by the dry powder magnetic magnet ic partic particle le metho method. d. 1.2 These reference photographs photographs are intended to assist in the classification of those discontinuities revealed in ferrous castings subjected to magnetic particle examination. 1.3 These reference reference photographs photographs are intended intended to be used for purposes purpo ses of comparison with the magnetic partic particle le indica indications tions observed on actual castings. 2. Referenc Referenced ed Documents Documents 2.1   ASTM Standards:3 E709  Guide for Magnetic Particle Testing 2.2   ASTM Adjuncts: Reference Refere nce Photo Photograph graphss for Magnet Magnetic ic Particle Indications Indications2 3. Ident Identifica ification tion 3.1 The typ types es of dis discon contin tinuiti uities es cov covered ered by the ref refere erence nce photographs are listed and described in  Table 1. 1.  Each type of  discontinuity discon tinuity is design designated ated by Roman numerals I throu through gh VIII as given in the table. 3.2 The deg degree reess of dis discon continu tinuity ity sev severit erity y, in inc increa reasin sing g order where applicable, are denoted by numbers 1 through 5. NOTE  1—To avoid any misunderstanding, it should be pointed out there is no correlation between degrees of the various defects. For instance, Degree 3 of Type I is not equivalent to Degree 3 of Type II. 1 These reference photographs are under the jurisdiction of ASTM Committee E07  on Nondestructive Testing and are the direct responsibility of Subcommittee E07 on E07.03   on Liquid Penetrant and Magnetic Particle Methods. E07.03 Current edition approved Dec. 15, 2008. Published December 2008. Originally approved in 1963. Last previous edition approved in 2003 as E125 – 63 (2003). DOI: 10.1520/E0125-63R08. 2 These reference photographs are available on four large charts arranged for each type of discontinuity. The charts are available from ASTM Headquarters. Order ADJE0125.. ADJE0125 3 For refere referenced nced ASTM stand standards, ards, visit the ASTM websi website, te, www www.astm .org,, or contact ASTM Customer Service at [email protected] For  Annual Book of ASTM  Standards volume information, refer to the standard’s Document Summary page on the ASTM website. 3.3 Each reference reference photograph photograph is identified with the proper number and letter designation. 4. Preparat Preparation ion 4.1 The reference photographs photographs represent magnetic particle indications as found on production steel castings. They represent se nt th thee act actua uall siz sizee of th thee in indi dicat catio ions ns an and d th thee pr proc oced edur uree follo fo llowe wed d wa wass in ac acco cord rdan ance ce wi with th Gu Guid idee   E709. E709.   The pe peak  ak  magnetizing magne tizing current current employed employed was from 600 to 800 A and prod spacing from 4 to 10 in. 4.2 The white line indicatio indications ns as illu illustr strated ated in most of the photographs were obtained by painting the casting area with a slurry of lamp-black in kerosene, gasoline, or alcohol. A gray magnetic powder is then used. The result is a white indication under normal photographic methods. 4.3 The blac black k lin linee ind indicat ication ionss res result ult fro from m app applyin lying g red magnetic magne tic powd powder er to the casting surface and photo photograph graphing ing the magnetic particle indications. 5. Basis for Use of Refe Referen rence ce Photographs Photographs 5.1 These reference reference photographs photographs are intended for use when they the y are spe specifi cified ed in the inq inquir uiry y, con contra tract, ct, ord order er,, mate materia riall specifications, or applicable code, and when the limiting class of severity is mutually agreed upon by the manufacturer and the purchaser purchaser.. It is adm admitte itted d tha thatt it is imp imposs ossibl iblee to rig rigidl idly y interpret magnetic particle indications on castings to a set of  photographic references; consequently there is a need for close cooperation between the manufacturer and the purchaser. 5.2 Unless otherwise otherwise specified specified all accessible surfaces surfaces of the casting shall be examined. On many castings, however, only certain cer tain are areas as are suf suffficie icientl ntly y cri critica ticall to jus justif tify y thi thiss typ typee of  examination. In these cases the locations to be examined shall be specifically agreed upon. 5.3 The sev severit erity y clas classs and the num number ber of cas casting tingss mad madee from the same pattern to be given magnetic particle examination shall constitute a part of the inquiry, contract, or order, or shall be as specified in the material specification or applicable code. Copyright. (C) ASTM International, 100 Barr Harbour Dr. P.O. box C700 West Conshohocken, Pennsylvania 19428-2959, United States Copyright by ASTM Int'l (all rights reserved); reserved); Thu Feb 2 16:12:20 EST 2012 1 Downloaded/printed by James Draper (Draper+NDT+Services+and+Consulting,+L.L.C.) pursuant to License Agreement. No further reproductions authorized. E125 – 63 (2008) TABLE 1 Types of Discontinuities Type I Type of Discontinuity Linear discontinuities (hot tears and cracks) Figure No.A Degree 1 2 3 I-1a, I-1b and I-1c Definition Ragged lines of variable width. May appear as a single jagged line or exist in groups. They may or may not have a definite line of continuity. They usually originate at the casting surface and generally become smaller as they go deeper. I-2a, I-2b and I-2c I-3a, I-3b and I-3c I-4a, I-4b and I-4c I-5a, I-5b and I-5c 4 5 (3 examples each) II Shrinkage 1 to 5 II-1, II-2, II-3, II-4 and II-5 Appears as a jagged area or irregular patches. Shrinkage is a subsurface discontinuity that may be brought to the surface by machining or other methods of metal removal. III Inclusions 1 to 5 III-1, III-2, III-3, III-4 and III-5 Isolated, irregular or elongated variations of magnetic particles occurring singly, in a linear distribution or scattered at random in feathery streaks. The indications are the result of the presence of sand, slag or oxides in the surface metal. IV Internal chills and unfused chaplets 1 to 5 IV-1, IV-2, IV-3, IV-4 and IV-5 A uniform line or band outlining the object and indicating lack of fusion between the metal object and the casting. V Porosity 2 examples V-1 and V-2 Appears as rounded and elongated clusters of magnetic particles of various sizes; scattered at random. VI Welds: Weld porosity Incomplete penetration Undercutting Inclusions in weld Crater cracking 5 examples False Indications: Prod pattern Powder lodged in surface depression Particles dropped from cables Chisel marks Wrinkles 5 examples Magnetic Anomalies: Adhering scale Magnetic writing High external magnetic field Junction of materials of different permeability Powder build up at sharp fillet 5 examples VII VIII A VI-1 VI-2 VI-3 VI-4 VI-5 Incomplete fusion and penetration appears as a straight continuous or intermittent linear indication. Porosity, inclusions and linear discontinuities in welds appear as described above. VII-1 VII-2 VII-3 VII-4 VII-5 VIII-1 VIII-2 VIII-3 VIII-4 VIII-5 See Footnote 2. 5.4 The limiting size and shape of the unit area to be examined shall be established by the applicable code or by mutual agreement of the manufacturer and the purchaser. When more than one type of discontinuity appears in the specified area, agreement on this situation should be established. 5.5 These indications, generally, represent evidence of surface discontinuities and any deductions or conclusions with regard to depth or extent of the interior nature of the discontinuity must be based on exploration by other test methods. 6. Keywords 6.1 discontinuities; ferrous castings; indications; magnetic particle indications; magnetic particle examination; magnetic particle inspection; photographs; reference photographs; steel castings Copyright by ASTM Int'l (all rights reserved); Thu Feb 2 16:12:20 EST 2012 2 Downloaded/printed by James Draper (Draper+NDT+Services+and+Consulting,+L.L.C.) pursuant to License Agreement. No further reproductions authorized. E125 – 63 (2008) ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned  in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk  of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and  if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards  and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the  responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should  make your views known to the ASTM Committee on Standards, at the address shown below. This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above  address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website  ( Copyright by ASTM Int'l (all rights reserved); Thu Feb 2 16:12:20 EST 2012 3 Downloaded/printed by James Draper (Draper+NDT+Services+and+Consulting,+L.L.C.) pursuant to License Agreement. No further reproductions authorized.