Transcript
Page 1 of 17
Upgrading ECU’s on BMW F11 520d
Disclaimer: All content in this document d ocument is to be seen as guidelines. No one but yourself can take responsibility if you break something as a consequence of following this guide. The author can in NO WAY be held liable or responsible if you mess up something / anything.
Upgrading ECU’s on BMW F11 520d
Page 2 of 17
Remember always to create a backups before starting an endeavour like this!
All this could not have been done without primarily shawnsheridan @ bimmerfest and a bunch of other users.
Prerequisites: ENET cable, E-Sys 3.26.0, PsdZData files (54.0 is used in this guide). It’s important that the PsdZData files are the FULL version as the Lite version does not include all necessities for flashing. And last prerequisite: a BMW F10 or F11. I’m doing this on my F11 520d. This guide should work for all Fxx chassis. E-Sys 3.26.0 is used for screen dumps. Other versions may differ slightly. In this document, I’ll be upgrading these ECU’s:
CMB_MEDIA
HU_CIC
KOMBI
ZGW
The steps for upgrading other ECU’s should be the same as doing these four. Just remember to identify the
dependencies and select appropriately in step 15 in the below procedure. When flashing involves ZGW it is widely said that the ZGW module should be updated BEFORE other modules. The TAL (transaction list) generated by E-Sys should take care of this. But if you want, you could flash the ZGW all by itself and then restart and do the rest. The steps remain the same. Flashing all modules at once is also as easy as flashing individual modules. Just select all the modules in step 15 (still blFlash, swDeploy, cdDeploy, and ibaDeploy columns) HU_CIC Depends (PreRequisites) on: 38 + 14 (BOTH ZGW) KOMBI Depends on: 38 + 10 + 14 + 53 + 57 (ZGW + HU_CIC + ZGW + CMB_MEDIA + HU_CIC) CMB_MEDIA Depends on: 57 (HU_CIC) ZGW does not have dependencies. How to identify dependencies: http://www.bimmerfest.com/forums/showpost.php?p=8688725&postcount=18
HU_CIC:
Upgrading ECU’s on BMW F11 520d
Page 3 of 17
KOMBI:
CMB_MEDIA:
Upgrading ECU’s on BMW F11 520d
Page 4 of 17
ZGW:
Basic steps (src: http://www.bimmerfest.com/forums/showpost.php?p=8179840&postcount=29): 1. Connect external charger (at least 50AMPs, preferably 70AMPs) to the car battery. Connect laptop to power supply. This step is essential! 2. Turn lamp switch to parking light – this will keep the ignition on beyond 20 minutes. (src: http://www.bimmerfest.com/forums/showthread.php?p=8625168&highlight=parking+light+switch #post8625168). Please refer to Appendix B for further info regarding the light switch and the 20 minutes. 3. Connect via “Connection via Gateway URL” (src: http://www.bimmerfest.com/forums/showthread.php?t=698424, post #6) (else flashing ZGW will fail)
Upgrading ECU’s on BMW F11 520d
Page 5 of 17
4. Select Comfort Mode TAL Calculating
5. Read and save FA
Upgrading ECU’s on BMW F11 520d
Page 6 of 17
6. Activate FA
7. Read and save SVT Actual as “SVT_ist”
8. Create an SVT Target: a. Select Complete Flash
b. Select I-Step (shipm.) to match vehicles shipment I-Step level (src: http://x3.xbimmers.com/forums/showthread.php?t=715297) i. Select Expert Mode VCM button
Upgrading ECU’s on BMW F11 520d
Page 7 of 17
ii. On the right bottom box, select “Master” tab
iii. In I-Steps box, click on “Read” button.
iv. Integration Steps boxes above will be populated with the data. Note down the IStep (Shipment).
Upgrading ECU’s on BMW F11 520d
Page 8 of 17
c.
I-Step (target.) will be unselectable as it is fixed based on current PSdZData I -Level. Select the appropriate level in I-Step (shipm.) as obtained in step above
d. Do a KIS/SVT Target Calculation and Save as “SVT_soll”
Upgrading ECU’s on BMW F11 520d
Page 9 of 17
e. Do a TAL Calculation and Save as “SVT_tal”
9. Go to Expert Mode TAL-Processing
10. Load TAL [SVT_tal) created in step 8.e
11. Load SVT Target (“SVT_soll”) created in step 8.d
Upgrading ECU’s on BMW F11 520d
Page 10 of 17
12. Click the “Read FA” button
this will result in the FA_aus_VCM.xml file:
13. Check radio button for "read VIN out of FA" and click the “Read VIN” button
14. On ECU Tab, uncheck let top box in column "All" (All checked boxes should toggle to unchecked)
15. On ID Base Row for HU_CIC, CMB_MEDIA, KOMBI and ZGW check the boxes in blFlash, swDeploy, cdDeploy, and ibaDeploy (please see Appendix C) columns.
16. Press Check software availability (this, among o ther, ensures that you have the correct P SdZdata and the FULL version of them)
Upgrading ECU’s on BMW F11 520d
Page 11 of 17
17. Press Start and it will proceed with processing TAL to flash Kombi with new firmware
18. Cross your fingers and watch it work
Upgrading ECU’s on BMW F11 520d
Page 12 of 17
Troubleshooting If coding ACSM, the airbag needs be locked. This can be done by using the following procedure (src: http://www.bimmerfest.com/forums/showthread.php?t=796371 post #3) (another good src: http://www.bimmerfest.com/forums/showthread.php?t=809906). E-Sys Transmitter: 1) Click "External Applications" in the left menu. 2) Click "External Application" 3) Double-click "Transmitter" 4) Double-click "ACSM verriegelung_schreiben"
Upgrading ECU’s on BMW F11 520d
Page 13 of 17
Appendix A – list of ECU’s Thanks to shawnsheridan on bimmerfest.com for compiling this list. (src: http://www.bimmerfest.com/forums/showthread.php?t=808412).
AAG - Trailer Hitch Module ACC - Active Cruise Control ACSM - Advanced Crash and Safety Management AHM - Trailer module AMP - Amplifier AMPH - HiFi Amplifier AMP_TOPHB - Top HiFi Amplifier/System AMP - Amplifier/System AMP_TOPHB - Top HiFi Amplifier/System ASA - Active steering ASD - Active Sound BDC - Body Domain Controller (ZGW, FEM, REM, SZL, IHKA, TCB, CAS, JBBF Combined) CAS - Car Access System CID - Central Information Display CMB_ECALL - Combox Emergency Caller CMB_MEDIA - Combox Media CVM - Soft top module (Convertable Top) DKOMBI - MFID Instrument cluster (6WB) DDE - Digiatl Diesel Electronics DME - Digital Motor Electronics DSC - Dynamic Stability Control DWA - Immobilizer (Alarm) DVDC - DVD Changer EGS - Electronic Transmission Control Unit EHA - Electronic ride-height control EHC - Electronic ride-height control
Upgrading ECU’s on BMW F11 520d
Page 14 of 17
EKPM - Electronic fuel pump control EMF - Electromechanical parking brake EPS - Electronic power steering FEM_BODY - Front electronics module (ZGW, FRM, CAS, and JBBF Combined) FEM_GW - Front electronics module gateway FKA - Rear-cabin automatic A/C FLA - Automatic High Beam Camera Only FRM - Footwell module (Lighting) FRR - Active cruise control FZD - Function unit roof GWS - Gear selection switch HKFM - Rear Lift-Lid (Trunk) HKL - Rear Lift-Lid (Trunk) HU_ENTRY - Head Unit Entry Level ( no iDrive System) HU_CHAMP (Head Unit CIC Mid) (iDrive system) HU_CIC - Head Unit CIC High (iDrive system) HU_NBT - Head Unit NBT (iDrive system) HC2 - Lane Change Warning HUD - Heads-Up Display ICM_QL - Integrated Chassis Management ICM_V - Integrated Chassis Management Vertical (Vertical dynamics management) IHKA - Integrated automatic heating/air conditioning system JBBF - Junction box electronics JBE - Junction box electronics KAFAS - Cameras System (LDW, AHB, SLI) KOMBI - Instrument cluster LHM - LED Headlights main light modules (fan and LEDs for the cornering light, low-beam and high-beam headlights). NIVI - Night Vision Camera PDC - Park distance control
Upgrading ECU’s on BMW F11 520d
Page 15 of 17
PMA2 - Parking Assist RDC - Tyre pressure control REM - Rear Electronics Module RSE - Rear Seat Entertainment SM - Seat module / Seat Memory SME - Accumulator-management electronics SMBF - Seat module / Seat Memory Passenger SZL_LWS - Steering column control unit SVT - Servotronic TCB - Telematics Communications Box (BMW Assist) TMS - LED Headlights (stepper motors for the Adaptive LED Headlights and LEDs for the side marker light, the positioning light and the turn indicator) TRSVC -All around view camera TBX - iDrive Controller Touch Handwriting Module VDM - Vertical dynamics Management ZBE - iDrive Controller ZGW - Central gateway module
Upgrading ECU’s on BMW F11 520d
Page 16 of 17
Appendix B On new cars (7/2014 F30) the ignition will not stay on even if you turn light switch. After 15 minutes or so ignition will turn off. This is not a pro blem though, just remember to cycle ignition before svt soll calculation and before starting TAL processing (actual flash). Ignition will stay on as long as the TAL is running. Thank you ap90500, src: http://www.bimmerfest.com/forums/showpost.php?p=8737326&postcount=2
Upgrading ECU’s on BMW F11 520d
Page 17 of 17
Appendix C ibadeploy is needed only if you are flashing a headunit that has IBA (electronic user manual). It doesn't do any damage if it is selected without a reason though. Thank you ap90500, src: http://www.bimmerfest.com/forums/showpost.php?p=8737326&postcount=2
Upgrading ECU’s on BMW F11 520d